FAQ

• LCD front panel password is 0000.
• WEB Management user name is admin.
• WEB Management password is Admin123.

This is a resolution issue. Before connecting to the digi-MOD HD, ensure the output resolution of the source device is 1080p (MPEG-4/H.264), 1080i or 720p. PC resolutions like 1,336 x 768 will not display through a modulator.

There is no input signal present at your digi-MOD HD. Check the source is powered and connected properly.

If the TV does not find the new channel, the TV may not have an MPEG4/H.264-compatible tuner. Before purchasing try and see if your TV can view Racing Channel or 9HD. If your TV can receive these channels then it has a MPEG-4 tuner.

Check your cabling. Check that the correct programming changes have been carried out. Check the channel that has been programmed is clear from any other FTA transmission.

Check the signal levels of FTA and the modulator and make sure the levels are close to each other (5dB separation). If the modulator signal level is higher than the FTA, the FTA signal may be effected by the modulator C/N. Balancing will rectify this.

Yes. Follow the set-up requirements in the install manual.

Yes. With the optional RL-ACC500 rack ears and screw pack the digi-MOD RL-DM4000D will fit into a 1 RU space.

Yes – you just need to adjust some of the settings in each modulator. Each digi-MOD is defaulted to the same settings – see below changes that need to be made for “stack” successfully.

1. Output Channel – Default “39 UHF”
2. LCN – Default “101”, Modulator will work if not changed, it will just be located on 350. 351 etc.
3. Channel Name – Default “CHANNEL-1” Modulator will work if not changed, just harder to identify
4. Program Number – Default “1” Modulator still may work but best to change in case (suggest using LCN #)
5. TSID – Default “1000” Modulator will not work as each channel requires a separate TSID

These changes can be done via Front LCD Display or GUI.

We suggest employing the services of an experienced installer, who has test equipment to determine signal strength and quality. This will allow them to determine how best to solve your problem. If there is too much electrical noise in your environment, tuners will have difficulty decoding the low signal over the noise, resulting in either pixelation or a completely frozen screen.

Approximately 60m, depending on environmental interference.

• Antenna: +2dB (adjustable)
• Modulator: +3dB.

IR function out of the digi-MOD emitter port will only work if the only power supply is connected to the modulator and the remote power switch is “ON”. If there is a power supply connected to the RL-RF380 – the IR will not work out of the modulator, only the IR emitter port on the RL-RF380.

After checking all cable connections, check to see if a non resi-linx RF splitter that does not pass DC or IR is connected to the corresponding RL-RF380 output/s. Remove or replace. Check coax input and output are on the correct ports.

Each digi-MOD HD now has a static IP Address – 192.168.1.9.

If you are unable to access via IP Address, simply change setting in digi-MOD HD “WEB MANAGEMENT” – DHCP from “DISABLE” to “ENABLE”, then find the digi-MOD HD in networks.

Note – currently digi-MOD’s can only be used with Windows operating platform.

If your TV has an MPEG-2 tuner only, it will still can a MPEG-4  (H.264) modulator but you will only hear the audio – you will get no picture. To rectify this – either use a MPEG-4 STB on this TV or change your modulator to a MPEG-2 modulator – or buy a new MPEG-4 TV…

Yes – we now have a local service agent.

Unitech Services

13 Maroondah Highway

Croydon VIC 3136

03 9725 2222

Foxtel Non-DRM Approved Channel Plan November 2019